LED drops and limit switch

Diagram

LED feeds L1-L3 (board to unplug point), pigtails L1p-L3p
to the three lamp strips, and the limit switch cable.
%3 BOARD_L1 BOARD_L1 Dupont 1x2 female, 2.54 mm 2-pin GND 1 +24V 2 On basically board v1.3, J8, J9 or J10. Black goes in the cavity at the moulded arrow: that end goes over the pin printed GND. L1 L1 2x 22 AWG 36.0 in   BOARD_L1:1:GND     1:BK     LJ1:2:GND (sleeve) BOARD_L1:2:+24V     2:RD     LJ1:1:+24V (tip)   LED feed. Black at the board end arrow. BOARD_L1:e--L1:w BOARD_L1:e--L1:w LJ1 LJ1 DC jack 5.5x2.1 female, inline 2-pin 1 +24V (tip) 2 GND (sleeve) Unplug point. LP1 LP1 DC plug 5.5x2.1 male 2-pin +24V (tip) 1 GND (sleeve) 2 LJ1:e--LP1:w BOARD_L2 BOARD_L2 Dupont 1x2 female, 2.54 mm 2-pin GND 1 +24V 2 On basically board v1.3, J8, J9 or J10. Black goes in the cavity at the moulded arrow: that end goes over the pin printed GND. L2 L2 2x 22 AWG 36.0 in   BOARD_L2:1:GND     1:BK     LJ2:2:GND (sleeve) BOARD_L2:2:+24V     2:RD     LJ2:1:+24V (tip)   LED feed. Black at the board end arrow. BOARD_L2:e--L2:w BOARD_L2:e--L2:w LJ2 LJ2 DC jack 5.5x2.1 female, inline 2-pin 1 +24V (tip) 2 GND (sleeve) Unplug point. LP2 LP2 DC plug 5.5x2.1 male 2-pin +24V (tip) 1 GND (sleeve) 2 LJ2:e--LP2:w BOARD_L3 BOARD_L3 Dupont 1x2 female, 2.54 mm 2-pin GND 1 +24V 2 On basically board v1.3, J8, J9 or J10. Black goes in the cavity at the moulded arrow: that end goes over the pin printed GND. L3 L3 2x 22 AWG 36.0 in   BOARD_L3:1:GND     1:BK     LJ3:2:GND (sleeve) BOARD_L3:2:+24V     2:RD     LJ3:1:+24V (tip)   LED feed. Black at the board end arrow. BOARD_L3:e--L3:w BOARD_L3:e--L3:w LJ3 LJ3 DC jack 5.5x2.1 female, inline 2-pin 1 +24V (tip) 2 GND (sleeve) Unplug point. LP3 LP3 DC plug 5.5x2.1 male 2-pin +24V (tip) 1 GND (sleeve) 2 LJ3:e--LP3:w L1P L1P 2x 22 AWG 6.0 in   LP1:1:+24V (tip)     1:RD     STRIP1:1:+24V LP1:2:GND (sleeve)     2:BK     STRIP1:2:GND   LED pigtail. LP1:e--L1P:w LP1:e--L1P:w STRIP1 STRIP1 Solderless clamp-on strip connector 2-pin 1 +24V 2 GND LED strip, 6000K. Clamp-on connector instead of soldering. Pick the variant with IDC crimp points on both sides so it takes the pigtail wire as well as the strip. L2P L2P 2x 22 AWG 6.0 in   LP2:1:+24V (tip)     1:RD     STRIP2:1:+24V LP2:2:GND (sleeve)     2:BK     STRIP2:2:GND   LED pigtail. LP2:e--L2P:w LP2:e--L2P:w STRIP2 STRIP2 Solderless clamp-on strip connector 2-pin 1 +24V 2 GND LED strip, 6000K. Clamp-on connector instead of soldering. Pick the variant with IDC crimp points on both sides so it takes the pigtail wire as well as the strip. L3P L3P 2x 22 AWG 6.0 in   LP3:1:+24V (tip)     1:RD     STRIP3:1:+24V LP3:2:GND (sleeve)     2:BK     STRIP3:2:GND   LED pigtail. LP3:e--L3P:w LP3:e--L3P:w STRIP3 STRIP3 Solderless clamp-on strip connector 2-pin 1 +24V 2 GND LED strip, 6000K. Clamp-on connector instead of soldering. Pick the variant with IDC crimp points on both sides so it takes the pigtail wire as well as the strip. BOARD_LIM BOARD_LIM Dupont 1x3 female, 2.54 mm 3-pin GND 1 SIG 2 +3V3 3 On basically board v1.3, J5 (HALL_SW_0). Pin order read off the v1.3 netlist. Position 1 is the cavity at the moulded arrow. Position 3 is deliberately unpopulated: it lines up with the 3.3 V pin, so the plug cannot go on backwards. LIM LIM 2x 22 AWG 24.0 in   BOARD_LIM:1:GND     1:BK     SW:1:GND BOARD_LIM:2:SIG     2:WH     SW:2:SIG   Limit switch. Black ground, white signal. BOARD_LIM:e--LIM:w BOARD_LIM:e--LIM:w SW SW Quick-connect receptacle, #187 (4.75 x 0.5 mm tab) 2-pin 1 GND 2 SIG Omron V-155-1C25, quick-connect (#187) tabs. These push on, no soldering. Fully insulated: the switch is SPDT and the third tab is unused. L1:e--LJ1:w L1:e--LJ1:w L2:e--LJ2:w L2:e--LJ2:w L3:e--LJ3:w L3:e--LJ3:w L1P:e--STRIP1:w L1P:e--STRIP1:w L2P:e--STRIP2:w L2P:e--STRIP2:w L3P:e--STRIP3:w L3P:e--STRIP3:w LIM:e--SW:w LIM:e--SW:w

Bill of Materials

Id Description Qty Unit Designators
1 Cable, 2 x 22 AWG 150 in L1, L1P, L2, L2P, L3, L3P, LIM
2 Connector, DC jack 5.5x2.1 female, inline, 2 pins 3 LJ1, LJ2, LJ3
3 Connector, DC plug 5.5x2.1 male, 2 pins 3 LP1, LP2, LP3
4 Connector, Dupont 1x2 female, 2.54 mm, 2 pins 3 BOARD_L1, BOARD_L2, BOARD_L3
5 Connector, Dupont 1x3 female, 2.54 mm, 3 pins 1 BOARD_LIM
6 Connector, Quick-connect receptacle, #187 (4.75 x 0.5 mm tab), 2 pins 1 SW
7 Connector, Solderless clamp-on strip connector, 2 pins 3 STRIP1, STRIP2, STRIP3